Sonicwall Ha Is Currently Synchronizing Please Try Again Later
HA_Status
High Availability > Status
The following sections draw the High Availability > Condition folio:
• Active/Standby High Availability Status
• Active/Active High Availability Status
Active/Standby High Availability Status
The High Availability Status table on the Loftier Availability > Condition page displays the current status of the HA Pair. If the Chief SonicWALL is Agile, the get-go line in the tabular array indicates that the Main SonicWALL is currently Active.
It is also possible to cheque the condition of the Secondary SonicWALL by logging into the unique LAN IP address of the Secondary SonicWALL. If the Principal SonicWALL is operating normally, the status indicates that the Secondary SonicWALL is currently Standby. If the Secondary has taken over for the Primary, the condition table indicates that the Secondary is currently Active.
In the outcome of a failure in the Chief SonicWALL, you lot tin access the management interface of the Secondary SonicWALL at the Primary SonicWALL virtual LAN IP address or at the Secondary SonicWALL LAN IP address. When the Primary SonicWALL restarts after a failure, it is accessible using the unique IP address created on the High Availability > Monitoring page. If preempt style is enabled, the Master SonicWALL becomes the Agile firewall and the Secondary firewall returns to Standby status.
The table displays the following information:
Loftier Availability Status
• Condition – Indicates the HA country of the Chief SonicWALL SuperMassive. The possible values are:
– Primary Agile – Indicates that the Primary HA appliance is in the Agile state.
– Main Standby – Indicates that this appliance is in the standby state.
– Master Disabled – Indicates that High Availability has non been enabled in the management interface of this apparatus.
– Principal not in a steady country – Indicates that HA is enabled and the appliance is neither in the Agile nor the standby state.
• Master Country - Indicates the current state of the Master appliance as a member of an HA Pair. The Primary State field is displayed on both the Primary and the Secondary appliances. The possible values are:
– ACTIVE – Indicates that the Master unit is handling all the network traffic except direction/monitoring/licensing traffic destined to the standby unit.
– standby – Indicates that the Primary unit is passive and is set to have over on a failover.
– Election – Indicates that the Primary and Secondary units are negotiating which should be the Active unit.
– SYNC – Indicates that the Primary unit is synchronizing settings or firmware to the Secondary.
– Fault – Indicates that the Chief unit has reached an fault status.
– REBOOT – Indicates that the Primary unit is rebooting.
– NONE – When viewed on the Principal unit of measurement, NONE indicates that HA is not enabled on the Primary. When viewed on the Secondary unit, NONE indicates that the Secondary unit is not receiving heartbeats from the Master unit.
• Secondary Country - Indicates the current country of the Secondary appliance equally a member of an HA Pair. The Secondary State field is displayed on both the Principal and the Secondary appliances. The possible values are:
– Active – Indicates that the Secondary unit of measurement is treatment all the network traffic except management/monitoring/licensing traffic destined to the standby unit.
– STANDBY – Indicates that the Secondary unit is passive and is fix to take over on a failover.
– Election – Indicates that the Secondary and Chief units are negotiating which should be the ACTIVE unit of measurement.
– SYNC – Indicates that the Secondary unit of measurement is synchronizing settings or firmware to the Principal.
– Error – Indicates that the Secondary unit has reached an error condition.
– REBOOT – Indicates that the Secondary unit is rebooting.
– NONE – When viewed on the Secondary unit, NONE indicates that HA is non enabled on the Secondary. When viewed on the Primary unit, NONE indicates that the Main unit is not receiving heartbeats from the Secondary unit.
• Active Upward Time - Indicates how long the electric current Active firewall has been Agile, since it concluding became Active. This line simply displays when High Availability is enabled. If failure of the Primary SonicWALL occurs, the Secondary SonicWALL assumes the Principal SonicWALL LAN and WAN IP addresses. There are three primary methods to check the condition of the Loftier Availability Pair: the Loftier Availability Status window, Email Alerts and View Log. These methods are described in the following sections.
• Node Status - Indicates if Active / Agile Clustering is enabled or is not enabled.
• Found Peer - Indicates if the Primary unit has discovered the Secondary unit. Possible values are Yes and No .
• Settings Synchronized - Indicates if HA settings are synchronized between the Primary and Secondary units. Possible values are Yes and No .
• Stateful HA Synchronized - Indicates if stateful synchronization settings are synchronized betwixt the Primary and Secondary units. Possible values are Yes and No .
High Availability Configuration
• HA Manner - I method to make up one's mind which SonicWALL is Agile is to check the HA Settings Condition indicator on the High Availability > Settings page. If the Primary SonicWALL is Agile, the first line in the page indicates that the Main SonicWALL is currently Active . It is besides possible to cheque the condition of the Secondary SonicWALL by logging into the LAN IP address of the Secondary SonicWALL. If the Primary SonicWALL is operating normally, the condition indicates that the Secondary SonicWALL is currently Standby . If the Secondary has taken over for the Primary, the condition indicates that the Secondary is currently Active. In the event of a failure in the Primary SonicWALL, you can access the management interface of the Secondary SonicWALL at the Primary SonicWALL LAN IP address or at the Secondary SonicWALL LAN IP address. When the Main SonicWALL restarts afterward a failure, it is attainable using the third IP address created during configuration. If preempt way is enabled, the Master SonicWALL becomes the Active firewall and the Secondary firewall returns to Standby condition.
• HA Control Link – Indicates the port, speed, and duplex settings of the HA link, such every bit HA 1000 Mbps full-duplex , when two SonicWALL SuperMassives are connected over their specified HA interfaces. When High Availability is not enabled, the field displays Disabled .
• Secondary HA Control Link – Indicates the port, speed, and duplex settings of the secondary HA link, such as HA k Mbps full-duplex , when ii SonicWALL SuperMassives are continued over their specified HA interfaces. When High Availability is not enabled, the field displays Disabled .
Note HA enhancements are available in SonicOS 6.0.v.
• HA Data Link – Indicates the port, speed, and duplex settings of the HA link, such as HA 1000 Mbps total-duplex , when 2 SonicWALL SuperMassives are continued over their specified HA interfaces. When High Availability is not enabled, the field displays Disabled .
• Agile/Agile DPI Link – Indicates the port, speed, and duplex settings of the Agile/Active DPI link, such equally HA 1000 Mbps total-duplex , when two SonicWALL SuperMassives are connected over their specified HA interfaces. When Loftier Availability is non enabled, the field displays Disabled .
High Availability Licenses
• Primary Stateful HA Licensed - Indicates if the Primary apparatus has a stateful HA license. Possible values are Yes or No .
• Secondary Stateful HA Licensed - Indicates if the Secondary appliance has a stateful HA license. Possible values are Aye or No . Annotation that the Stateful HA license is shared with the Main, but that you lot must access mysonicwall.com while logged into the LAN management IP address of the Secondary unit in order to synchronize with the SonicWALL licensing server.
• Main Agile / Agile Licensed - Indicates if the Primary appliance has a Active / Active license. Possible values are Yes or No .
Active/Agile High Availability Status
The Loftier Availability > Condition page provides status for the unabridged Active/Active cluster and for each Cluster Node in the deployment. The status for the Agile/Active cluster is displayed in the upper table, and condition for the each Cluster Node is displayed in the lower table.
Figure l:16 Loftier Availability > Status Folio
For additional information on Loftier Availability status and verifying the configuration, see Verifying Agile/Active Clustering Configuration
Source: http://help.sonicwall.com/help/sw/eng/published/26.0.1_140828_1715/content/High_Availability/HA_Status.htm
0 Response to "Sonicwall Ha Is Currently Synchronizing Please Try Again Later"
Post a Comment